Index
Index forum Index forum
Autentificare Autentificare
Inregistrare Inregistrare
Cine este online Cine este online
Galerie imagini Galerie imagini
Calendar evenim. Calendar evenim.
Cautare detaliata Cautare detaliata
Ghid forum Ghid forum
Album astrofoto
moon.jpg
Imagine aleatoare
Blog
Inregistreaza-te pe forumul astronomy.ro
Colaboratori

Te intereseaza un domeniu al astronomiei si ai vrea sa scrii pentru siteul nostru? Alatura-te echipei noastre.

Meteo
Publicatii
STELE SI CONSTELATII, Marcel Jinca
Statistici forum
Numar total de mesaje in forum: 188708
Numar de utilizatori inregistrati: 2474
Cel mai nou utilizator inregistrat: yulyx
Cei mai multi utilizatori conectati au fost 399 la data de Joi Dec 31, 2015
Actualmente sunt 0 utilizatori pe chat   
Aceste date se bazeaza pe utilizatorii activi de peste 5 minute
Legenda
Mesaje noi Mesaje noi
Nu sunt mesaje noi Nu sunt mesaje noi
Forumul este inchis Forumul este inchis

Autostar 494 LCD replacement


Creaza un subiect nou   Raspunde la subiect  

DIY / ATM / Reparatii

Subiectul anterior :: Subiectul urmator  
Afiseaza mesajele pentru a le previzualiza:   
Autor Mesaj
micrenda
Membru
Membru


Data inscrierii: 26 Mai 2011
Mesaje: 134



Localitate: Bucuresti

MesajTrimis: 29 Dec 2014 13:32 Download mesaj
Titlul subiectului: Autostar 494 LCD replacement
Raspunde cu citat (quote)

Hello

I had to replace a broken LCD screen of an Autostar 494. Unfortunately the original LCD module was impossible to find and the only solution was to buy a new Autostar (costing ~80 EUR).

I tried with success to adapt an external LCD module with a similar pin-out (I had to solder the pin to the existing flat cable) but I was not too satisfied about the solution (it was very fragile and ugly).

Two weeks ago I found in ebay a LCD glass module with a compatible flat cable (ERC1602-3 costing ~7 EUR): the only problem was it was bigger then the original so it needed to be fixed externally.
I used a 3D printing service (http://www.print3dbucuresti.ro) and to create a support: the costs of the support was very reasonable and the quality was better than I expected.

To help who can be in the same situation (the Autostar LCD modules are quite fragile) I created a guide where I detailed all the steps I did (it is in Italian language, but if needed I can translate in English).

The requirements are:
1. A broken autostar
2. ERC1602-3 LCD module
3. A solder and stain cable
4. 3D printer (or access to 3D printing service)
5. A good glue (Picatura or any cyan-acrilate glue)

You can find the STL files that can be used to print the support. I created it using FreeCad, if you needs the source files (to adapt to a different type of LCD module) you can just ask.

Guide:
https://www.dropbox.com/s/t4f11ovnrpguaqb/...%20494.zip

I hope it helps someone with the same problem.

Regards
Michele Renda

PS. You can reply in Romanian.



risultato finale ridotto.jpg
 Descriere:
Final result
 Marime fisier:  422.49 kb
 Vizualizat:  de 1446 ori

risultato finale ridotto.jpg


Sus
Afiseaza mesajele pentru a le previzualiza:   
Creaza un subiect nou   Raspunde la subiect   DIY / ATM / Reparatii
Download topic
Pagina 1 din 1
 
Mergi direct la:  
Nu puteti crea un subiect nou in acest forum
Nu puteti raspunde in subiectele acestui forum
Nu puteti modifica mesajele proprii din acest forum
Nu puteti sterge mesajele proprii din acest forum
Nu puteti vota in chestionarele din acest forum
Nu puteti atasa fisiere in acest forum
Puteti descarca fisiere in acest forum
© 2015 astronomy.ro
Termeni si conditii generale      Termeni si conditii forum      Contact